strip casting

The heat transfer mechanism and the main affecting factors of twin roll strip casting was discussed, and bulit the general heat transfer differential and difference eguation.

本文探讨了双辊薄带铸轧过程的传热机理和主要的影响因素，建立了广义条件下的热传导方程，并对潜热问题做了处理。

The effects of the technical parameters, e.g. tapping temperature, choice of ladle nozzle diameter, flow of melt steel, side dam, strip casting speed, roll pressure, protective gas et, al, on quality of casting strip have been investigated.

同时对出钢温度、钢包水口直径的选择、布流形式、侧封技术、铸带速度、轧制力、保护气氛等工艺参数对铸带质量的影响进行了研究。

The result show that technology of strip casting can eliminate segregation and refine grain.

结果表明,利用薄带直接铸轧新工艺可消除偏析,极大的细化晶粒.

Numerical analysis on thermal stress of side dam on twin-roll strip casting

双辊铸轧薄带钢侧封板热应力的数值分析

Research on Superheat Control of Molten Steel During Twin-roll Strip Casting

双辊薄带铸轧过程钢液过热度控制研究

Research and Development of Mathematical Model of Twin-roll Thin Strip Continuous Casting Process

双辊薄带连铸过程的数学模型研究及其进展

Effect of Nozzle Spacer for Roll Strip Casting on Cavity Fluid Field

铝铸轧铸嘴分流块对型腔流场影响的研究

Discussion of casting and rolling process to make 3004 aluminium alloy strip plate

铸轧法生产3004铝合金带坯工艺探讨

Hazelett strip casting process is already successfully used for producing slug for impact extrusion.

哈兹列特铝板带连铸连轧工艺已被成功地用于铝和铝合金冲击挤压用坯料的生产.

The Experiment of Stainless Steel Casting Rolling Thin Strip Set

不锈钢铸轧薄带机组的工艺试验

The peak value of the rolling pressure will increase with the increase of the casting speed and the casting arca, the decrease of the strip being rolled, and the increase of the diameter of the casting roll.

随着铸轧速度与铸轧区增大、铸轧坯厚度减薄、铸轧辊径增大，轧制压力峰值增大。

Preparation of high performance Nd Fe B sintered magnet by strip casting ( SC ) process was studied.

研究了采用SC(stripcasting ) 工艺制备的高性能烧结钕铁硼磁体.

Water Modeling Study on Twin-roll Continuous Casting of Thin Strip Stock

双辊薄带连铸水模实验研究

Temperature Fields Finite Element Analysis on the Twin Roll Strip Casting

双辊铸轧薄带钢温度场的有限元分析

Simulation Investigation of Metal Delivery System for Twin-roll Strip Casting Process

双辊薄带连铸布流系统的模拟优化研究

Therefore, researching and resolving the sticky issues of thin aluminum strip in the process of casting roll is the key of rapid thin strip casting.

所以研究和解决铸轧过程中薄铝带坯的粘辊问题是实现薄带快速铸轧的关键。

Nonlinear thermal coupling FEM was used to investigate the temperature field and thermal deformation of roll sleeve during twin-roll strip casting.

利用非线性热力耦合有限元方法，对浇铸过程中结晶辊辊套的温度场分布进行了研究，并同时计算出了结晶辊的热变形。

The near net shape thin strip casting process, a competitive new technology, can simplify procedure, save energy, reduce energy consumption and cost.

近终形薄带连铸是钢铁工业简化工序、节能降耗、降低成本最具有竞争能力的一项重大新工艺技术。

In order to optimize the configuration of the feeding flow system in the twin-roll continuous casting process of thin strip stock, hydraulic simulation tests have been carried out on the liquid flow in the pool and the fluctuation of flow level measured with a level detector.

为优化双辊薄带连铸布流系统的结构，通过水力学模拟研究了双辊溶池内流体的流动，并使用浪高仪对双辊溶池内的液面波动进行了测量。

A brief introduction to the preparation of metallographic specimen of NdFeB ingot or strip casting are given in this article.

文章介绍了钕铁硼铸块或速凝薄带的金相样品的制备方法。